Correct Replacement Cab End Corner and Weather Seal for a TruXedo TruXport Tonneau Cover

Question

Question:

only need one passenger ft corner do i have to buy every thing. 2022 ram 1500 5.7 box

asked by: Richard

0

Expert Reply:

You're going to have to purchase the entire kit if even if you only need one side. The Replacement Cab End Corner and Weather Seal Kit for TruXedo TruXport Tonneau Covers # TX1118262 is only sold as a complete kit.

expert reply by: Bryce D

0

Answer 1

Yes, the Replacement Cab End Corner and Weather Seal Kit for TruXedo TruXport Tonneau Covers #TX1118262 would be a compatible fit for your cover. If you need to replace the rear caps as well then you'll need part #TX1704534, #TX1704535 , and…

view full answer...

Answer 2

If you are having trouble leveling the trailer using the auto-level feature then I first recommend extending each jack leg out at least 6" inches and then pressing and holding the retract button until the legs have fully retracted. This should…

view full answer...

Answer 3

The best method to identify the tonneau cover on your 2008 GMC Sierra will be to look for the date code and or serial number. The serial number is located on the driver's side of the front header on the TruXport frame. The date code is printed on…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The Triple-Axle Trailer Hanger Kit #APTT3 that you referenced is designed to work on axles with capacities of 2,000 lbs to 7,000 lbs so it should work very well for you. I attached a picture that has a chart that shows exactly how you should space…

view full answer...

Answer 6

In order to calculate where the axles would go on your trailer, there are several things that need to be taken into consideration. You will have to mock up the trailer with the suspension and axles to get the weights needed to determine where the…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...