What Hangers Do I need For My Heartland Cyclone 5th Wheel Toy Hauler?

Question

Question:

I am looking to replace my equalizers AND hangers on my Heartland Cyclone triple axle 5th wheel. I have the MORryde CRE3000 in mind, 33” wheel base. However I don’t see the proper hangers on your site.

asked by: David S

0

Expert Reply:

The CRE3000 Equalizers # MR59ZR are a great choice for an equalizer upgrade, but there is not a specific hanger set that would go with them. I can definitely help and point you in the right direction. Now, I do not have a way to know specs on your hangers based on a make and model of camper. If only it were so easy!

When replacing hangers it is important that we get the height of the hanger correct. This was we can retain the factory ride height. For example part # 28-5 is a very common hanger and measures 3-1/4" tall from the top of the hanger to the center of the hole. This is made for a 1-3/4" wide leaf spring. If you have 2' wide springs you could use a hanger like part # 721584, which is 3-9/16" tall.

If you are able to take a few quick measurements on the current hangers, we will have a very good idea of what height you will need. Keep in mind that with triple axle setups, the front, middle, and rear hangers can be different heights.

expert reply by: Jesse M

0

Answer 1

Measure the shackle strap lengths from hole center to hole center and you'll know which kit to get. If the distance is 2-1/4 inches long you'd want the part #MR86ZR or if they are instead 3-1/8 inches you'd want the part #MR26ZR. Those…

view full answer...

Answer 2

When upgrading your 2006 Weekend Warrior triple axle The MORryde Rubber Equalizers for Triple Axle Trailers - 35" Wheelbase - 8K #MR39ZR will work. This kit will upgrade your trailer's suspension system with rubber equalizers for a smoother,…

view full answer...

Answer 3

The MORryde Suspension Upgrade Kit #MR26ZR is designed to be used with the MORryde Rubber Equalizers for Triple Axle Trailers #MR39ZR. This equalizer kit only requires 6 sets of shackles as it removes one set of the shackles and allows the leaf…

view full answer...

Answer 4

For upgraded shackles on your 2020 Heartland Cyclone 4007 5th wheel I recommend one of our suspension upgrade kits. In order to select the correct kit you will need to know the length of your current shackles. If you have 2-1/4" shackle straps…

view full answer...

Answer 5

Since your 2016 Forest River Vengeance Model 39R12 has 33" axle spacing and triple axles the #MR59ZR will likely work just fine for you, but you will need to take a few measurements first. The first measurement is from the bolt hole in the rear…

view full answer...

Answer 6

The Keystone Carbon 417 should have a 35" axle spread which can be confirmed by measuring from the center of each axle. In which case, we have options from both Dexter and MORryde. The MORryde Rubber Equalizers for Triple Axle Trailers part…

view full answer...

Answer 7

In order to choose the correct MORryde Shackle Upgrade Kit you'll need to know the length of your shackle straps. If you have 2-1/4" long shackle straps then you can use part #MR86ZR or if you have 3-1/8" long shackle straps you can use…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...