13k Demco Hijacker Autoslide that Fits OEM Rail Kit of 2020 Ram 2500

Question

Question:

What Demco 13k model # auto slide would be needed for a 2020 Ram 2500 short bed ? The camper weight is 10,000 lbs.

asked by: Rodney H

0

Expert Reply:

For a 13k Demco Hijacker Autoslide you would need the part # DM6141 for the main hitch assembly and then for the adapter plates to fit the Ram rail kit of your 2020 Ram 2500 you would want the part # DM99GV.

expert reply by: Jameson C

0

Answer 1

We typically recommend that any beds in the 6-1/2' to 6-3/4' range used a sliding hitch and bed shorter than that used a fixed hitch with a rotating pin box to enable enough clearance to make a full 90 degree turn. Since you have a 2022 Ram…

view full answer...

Answer 2

I took a look at the online copy of your 2017 Ram 3500 owner's manual. Based on the information I found, your Ram 3500 with the Cummins diesel motor has an extremely high 5th wheel towing capacity of 32,000 pounds. I do also recommend verifying…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

So the truck bed payload is different from the amount of pin weight a truck can tow. Reason being the payload is a weight rating for the bed of the truck which is a much thinner material but the pin weight connects directly to the truck frame which…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The B and W Patriot slider is the only hitch unfortunately that can't be adapted to fit the OEM rails of your 2024 Ram 2500 as none of the adapters can work with it. So Mike what that means is that no matter how you slice it...it's time for a…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

13k Demco Hijacker Autoslide that Fits OEM Rail Kit of 2020 Ram 2500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching