Replacement Hardware Kit for a Curt Trailer Hitch On a 2012 Land Rover Range Rover Sport

Question

Question:

Howdy. I am trying to find a refitting hardware kit for the curt 13456. I am planning to use the hitch I have on my new vehicle and so will need the kit that was supplied with the hitch when I bought it. Including bolt leader wires. Please advise. Thanks

asked by: Lee B

1

Helpful Expert Reply:

In order to get a replacement hardware kit for your Curt Trailer Hitch Receiver # 13456, you'll just need to order the Replacement Hardware Kit for Trailer Hitches # RHK.

This kit is going to include everything that would've originally come with the hitch including the fish wire (leader wire).

To order this kit, all you're going to need to do is put "13456" in the "Hitch Item Number" box and add it to your cart.

expert reply by: Bryce D

1

Answer 1

To get the mounting hardware to install the Curt Trailer hitch Receiver #13456 you were looking at you will need to use Replacement Hardware Kit #RHK. On the product page for the #RHK you will select Curt from the drop down menu and enter 13456 in…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Replacement Hardware Kit for a Curt Trailer Hitch On a 2012 Land Rover Range Rover Sport

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching