Replacement Electric Brake Shoes for 2006 T@B Camper Trailer

Question

Question:

Do you have replacement AL-KO brake shoes for a 2006 T@b camper trailer.

asked by: David G

1

Helpful Expert Reply:

We do have some replacement brake shoes compatible with AL-KO brake assemblies. These are for the manually-adjusted brakes though so you'll want to keep that in mind:

- 7" Electric Brake Assemblies # AKBRKR-S-7
- 10" Electric Brake Assemblies # AKBRKR-S-10
- 12" Electric Brake Assemblies # AKBRKR-S-12

expert reply by: Jon G

1

Answer 1

The bolt pattern of 5 on 5 inch that there are 5 studs and the distance across the bolt circle is 5 inches. Most likely you have the more common 5 on 4-1/2 inch bolt pattern like what the wheel of the #AM20537 has instead. I attached a help article…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 6

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 7

Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part number…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Replacement Electric Brake Shoes for 2006 T@B Camper Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching