Do I Need to Change to LED Flashers When Changing to LED Running Lights?

Question

Question:

Do I need to change my directional flasher when changing from incandescent tailights to GloLight LED Trailer Tail Light - Stop,Turn,Tail # STL101RKB?

asked by: Michael G

0

Expert Reply:

No, you do not. If you decide to change your flashers to LEDs down the road you will want to use the Load Resistor Kit for LED Turn Signals item # DI34ZR or an LED compatible flasher.

expert reply by: Jerred H

0

Answer 1

There is no specific preparation procedure required to change over your trailer's lighting from standard incandescent fixtures to the brighter, cooler-operating and more efficient LED types available now. LED lighting is a great way to both…

view full answer...

Answer 2

You should have no problem using the Tow Ready Wiring Harness #118248 on your 2007 Toyota Highlander with a trailer that has LED tail lights. The only time LED lights require something being changed is when you go from incandescent bulbs on a blinker…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Do I Need to Change to LED Flashers When Changing to LED Running Lights?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching