Compatible Pop & Lock Custom Tailgate Lock For A 2003 Toyota Tacoma

Question

Question:

Hi, first time customer, confirming. that the PAL5100 tailgate lock will fit a 2003 Toyota Tacoma TRD double cab 4x4. Also, instructions are included and simple enough not to need a separate video or document, correct? Thank you!

asked by: David B

0

Expert Reply:

The Pop & Lock Custom Tailgate Lock # PAL5100 is confirmed to fit a 2003 Toyota Tacoma and can be easily installed in just a few minutes. I've attached a picture below of the installation instructions for you as well.

expert reply by: Kevin C

0

PL5100 Installation Instructions
(click to enlarge)

Answer 1

The RAS Suspension Systems essentially preload your leaf springs making them stiffer to prevent sag. This will affect your unloaded ride quality but not as negatively as some other compatible suspension enhancements for your Tacoma. These systems are…

view full answer...

Answer 2

The RoadActive Suspension Custom Leaf Spring Enhancement Kit #RAS4511-T are stiffening your leaf springs and would help whether you were loading the bed with equipment or hauling a trailer. Either way it's a downward force on the bed and…

view full answer...

Answer 3

For your ARE camper shell, if it has frameless bonded glass I recommend the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers #PAL9555 or #PAL9772.

view full answer...

Answer 4

The correct Pop and Lock for your A.R.E. truck cap with the T-handle is the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers #PAL9555. This includes a new handle that will replace your current handle. So long as your current…

view full answer...

Answer 5

As long as your vehicle has power door locks and your ARE V-Series truck cap has a frame-less, bonded glass door with a 1-1/8" center hole for a rotary latch you can use the Pop & Lock Power Locking Handle, part #PAL9555. There are a few…

view full answer...

Answer 6

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work with your Leer Tonneau Cover on your 2012 GMC Sierra. This is actually the exact same part number as the product in your photo so it is a perfect…

view full answer...

Answer 7

Because your A.R.E. Topper has the actuating rods instead of a wire pulley setup you'll need to use the Pop & Lock Power Pop Remote Keyless Entry Kit for Hard Tonneau Covers #PAL9000, which will replace your old rotary latch. The actuating…

view full answer...

Answer 8

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps part #PAL9772 that you referenced does fit your ARE DCU camper shell on your 2011 Chevy Colorado.

view full answer...

Answer 9

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with the keyless…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Compatible Pop & Lock Custom Tailgate Lock For A 2003 Toyota Tacoma

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching