Replacement Taillight for 2006 Trailster Trailer

Question

Question:

I have a 2006 trailstar trailer, there is a number listed on my receipt for the trailer 4tm11be116b002219, Im not sure if this number tells you anything, Im looking for submersible rear trailer lights, this is a bass boat trailer, it measures approximately 80 inches from the outside of the fenders , any help with the appreciate it thanks!

asked by: Mike C

0

Expert Reply:

Thanks for the picture of your taillights, from that I can tell that the lights you have are the part # ST37RB for the driver side and the part # ST36RB for the passenger side.

expert reply by: Jameson C

0

Trailer Tailight
(click to enlarge)

Answer 1

The lights you have on your trailer are #ST37RB and #ST36RB. The replacement lenses are #A39RB for the front lens and #A37RB for the side marker.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...