Correct Backing Plates for etrailer Tandem Axle Teardrop Trailer Fenders

Question

Question:

Can you tell me if backing plate HP82FR is the correct backing plate for Fenders HP94VR and HP44VR? Also if it is not the correct backing plate could you tell me which one goes with each of these fenders? Thanks

asked by: Josh

0

Expert Reply:

The Backing Plate for Tandem Axle Trailer Fender # HP82FR you mention is the correct backing plate for both the Tandem Axle Teardrop Trailer Fenders - Rounded Edges # HP94VR and the Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers # HP44VR.

expert reply by: Bryce D

0

Answer 1

The Tandem Axle Trailer Fenders - Double Radius - Steel - 14" to 15" Wheels - Qty 2 #HP94VR are 65" long x 9" wide x 15" tall and they are designed to work with 33 to 35 inch on center axle spacing.

view full answer...

Answer 2

The Tandem Axle Teardrop Trailer Fenders part #HP44VR which are 66" long measure 9" wide. I have attached a photo below.

view full answer...

Answer 3

The two best trailer fender options we offer in the size you need are as follows: Tandem Axle Teardrop Trailer Fenders part #HP44VR - 66" long x 9" wide x 19-3/4" tall -Steel Tandem Axle Teardrop Trailer Fenders part #HP34VR - 65"…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...