Recommended Bedroom and Living Room AC Replacements for 2014 Grand Design Reflections 293RES

Question

Question:

Need air conditioner replacements for 2014 Grand design Refelection 293 RES NON Ducted. Our unit had a fire and we need both the living room with thermostat and Bedroom without thermostat. Cannot use anything from existing units. Prefer the Advent brand. Thanks

asked by: Deborah M

0

Expert Reply:

In order to replace the living room unit, I recommend the Advent Air RV Air Conditioner System part # ADV44FR which comes with the overhead unit, distribution box, and wall mount thermostat. In order to replace the bedroom unit, I recommend the Advent Air RV Air Conditioner part # ACM135B and Air Distribution Box w/ Built-In Thermostat for Advent Air RV Air Conditioners part # ACDB which will give you manual independent control. These units are both black in color and rated at 13,500 lbs just like your existing from what I found.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

We do offer a direct replacement for the Dometic Duo-Therm RV Air Conditioner. The Advent Air RV Air Conditioner part #ACM135 for 13.5K or part #ACM150 for 15K is what I recommend. This unit will be a plug and play fit and it will work with your…

view full answer...

Answer 11

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 12

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Recommended Bedroom and Living Room AC Replacements for 2014 Grand Design Reflections 293RES

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching