Instructions for Toe-In Adjustment on Demco Kar Kaddy SS Tow Dolly
Question:
Need instructions on setting the Toe-in on a Demco Kar Kaddy SS tow dolly.
asked by: Carl B
Expert Reply:
The toe-in adjustment steps for the # DM9713045 are as follows:
1. Put a mark on each side of the locking clamp on the tie rod.
2. Loosen the locking nuts on each end of the tie rod and then the four bolts on the tie rod locking clamp.
3. Turn the tie rod whichever direction is needed until you have a front measurement of 1/32” to 1/16” less than the back measurement.
4. Hold the tie rod and tighten the locknuts on each end.
5. Measure again to make sure the toe-in measurement has not moved.
6. Tighten the locking clamp bolts while holding clamp between the marks you previously put on the tie rod.
7. Reassemble the rest of the Kar Kaddy unit.
I have attached a picture of the instructions, which includes measuring the toe-in. The full written instructions are also attached below for your reference. This can be found on page 19.
Product Page this Question was Asked From
Demco Kar Kaddy SS Tow Dolly with Disc Brakes - Foldable - 4,800 lbs
- Trailers
- Tow Dolly
- Wheel Decks
- 4800 lbs
- Folding Tongue
- Cars/Trucks/SUVs
- 8-1/2W x 11L Foot
- Galvanized Steel
- Demco
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Demco Kar Kaddy SS Tow Dolly with Disc Brakes - Foldable - 4,800 lbs
- Shop: Curt Ball Mount for 2" Hitches - 7" Rise, 8-1/4" Drop - 9-3/8" Long - 10,000 lbs
- Shop: Demco Kar Kaddy X Tow Dolly w/ Disc Brakes - Tilt Bed Frame - 4,800 lbs - Wide Tread
- Video: Demco Kar Kaddy SS Tow Dolly Review
- Shop: Trailer Hitch
- Shop: Curt Ball Mount for 2" Hitches - 7" Rise, 8" Drop - 9-3/8" Long - 12,000 lbs
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Ball Mount for 2" Hitches - 8" Rise, 9-1/4" Drop - 14" Long - 5K
- Article: Trailer Wiring Diagrams
- Search Results: anti rattle ball mount
- Search Results: kar kaddy 3
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Video: Curt 2 Inch Hitch Ball Mount Review
- Q&A: How To Replace The King Pin And Bushing In A Demco Kar Kaddy SS Tow Dolly
- Video: Review of Demco Kar Kaddy SS King Pin Bushing - DM73VR
- Q&A: 2017 Ford Explorer Towing Options Tow Dolly vs Flat Towing
- Video: Review of Demco Trailers - Replacement Tilt Bed Latch Hardware Set - DM42VR
- Video: Review of Roadmaster Replacement Tow Dolly Stabilizer Bar - RM-921006
- Video: Review of Demco Kar Kaddy SS King Pin Dust Cap - DM83VR
- Q&A: Spare Tire For Demco Kar Kaddy SS
- Q&A: Tow Dolly for Honda Fit with Automatic Transmission
- Q&A: How to Fix Swaying Demco DM8669113 Kar Kaddy SS Tow Dolly
- Q&A: How To Bleed Disc Brakes
- Search Results: hitch
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch