How To Replace The King Pin And Bushing In A Demco Kar Kaddy SS Tow Dolly

Question

Question:

Need instructions on how to replace the king pin and bushing in demco Kar caddy. Thanks

asked by: Paul

0

Expert Reply:

There is a retainer bolt in the wheel carrier that holds the bushing and king pin in place in the Demco Kar Kaddy SS # DM9713045. You would need to remove the retainer bolt to release the king pin and replace it. This is a part that we do not currently offer so you would need to reach out to Demco for a replacement.

expert reply by: Kevin C

0

Demco Kar Kaddy SS Parts Diagram
(click to enlarge)

Answer 1

The toe-in adjustment steps for the #DM9713045 are as follows: 1. Put a mark on each side of the locking clamp on the tie rod. 2. Loosen the locking nuts on each end of the tie rod and then the four bolts on the tie rod locking clamp. 3. Turn the…

view full answer...

Answer 2

I reached out to Demco and confirmed that the current replacement parts will work on your older 2003 Demco Kar Kaddy. You will need the following: -Replacement King Pin Bushing #DM73VR -Replacement King Pin #DM63VR -Replacement Hub Assembly #DM04369

view full answer...

Answer 3

I took a look at the owner's manual for a 2018 Nissan Rogue and it stated that this vehicle cannot be flat towed, and can only use a tow dolly if you have a front wheel drive version. For this, the manual states to "Place the…

view full answer...

Answer 4

The Demco Kar Kaddy SS Tow Dolly with Disc Brakes part #DM9713045 uses disc brakes. The design is very similar to that of a modern day automobile. The wheel and hub/rotor are separate components. I have attached a diagram below. The recommended…

view full answer...

Answer 5

You CAN tow your Rogue behind a motorhome, but it cannot be flat towed with all 4 wheels down. FWD vehicles like your 2019 Nissan Rogue can't be safely flat towed because even with the vehicle place in Neutral, the transmission would still…

view full answer...

Answer 6

I spoke with our tire and wheel expert (30+ years in the business) and he stated that Demco is rounding the bolt pattern up to 115mm. This often happens with companies that do not manufacturer the tires and wheels. Wheel #DM11574 is indeed the…

view full answer...

Answer 7

Tire designations ST205/75D14 and ST205/75R14 are both for special trailer tires with a 205mm width, 75-percent aspect ratio and that fit a 14-inch wheel. The difference between them is the tire's type of construction. The ST205/75D14 tire is…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

How To Replace The King Pin And Bushing In A Demco Kar Kaddy SS Tow Dolly

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching