Can Curt Assure Brake Controller Install in 1992 Ford F-350

Question

Question:

Does this work om a 1992 ford f350

asked by: Hector L

0

Expert Reply:

Yes, the Curt Assure brake controller part # C49UR can work on your 1992 Ford F-350. All you need is the correct install harness part # C51312 which plugs in under the truck dash.

expert reply by: Jameson C

0

Answer 1

I believe you are simply asking the length of the king pin on the Trailair Rota-Flex 5th Wheel Pin Box #LC328330. I reached out to the manufacturer who said that the king pin on this pin box measured 3.29 inches. I have added a photo showing other…

view full answer...

Answer 2

There are a few different gooseneck options available for your 1993 Ford F-350 with overload springs, see link. But if you want to go with an industry leader I recommend the B&W Turnover ball #BWGNRK1110. The B&W products are solid, made in…

view full answer...

Answer 3

You can refer to the linked diagram to see the recommended minimum clearance dimensions for 5th wheel trailer towing. The specific design of the trailer's nose - is it tapered for better turning clearance or is it a flat-nose design? - affects…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...