Correct Replacement Circuit Board for the MaxxFan 4401K Roof Vent

Question

Question:

I am needing a replacement touch board for a maxxair fan 4401k. The part number is 1043010k. Do you have a replacement for this Thanks

asked by: Steve P

0

Expert Reply:

The correct replacement circuit board for your MaxxFan 4401K roof vent is the Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents # MA10-04301k-v16.

expert reply by: Bryce D

0

Answer 1

It sounds like the circuit board is faulty and for replacement we have the Replacement Printed Circuit Board part #MA10-04301k-v16 which should allow you to get your MaxxAir Vent Fan Model 4401K back up and running on the lowest speed setting. If you…

view full answer...

Answer 2

You will need a different fan like the MaxxFan Plus Roof Vent #MA00-04500K to have a remote controlled fan. The MaxxAir MaxxFan Mini Roof Vent #MA00-04401M is not capable of being used with a remote. The circuit board does not allow for this type of…

view full answer...

Answer 3

For your MaxxFan that is a 4301 Series the correct circuit board is the part #MA10-04301K-V16.

view full answer...

Answer 4

Yes. The Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents #MA10-04301k-v16 is the printed circuit board you need.

view full answer...

Answer 5

The Replacement Printed Circuit Board and Switch for MaxxFan Roof Vents #MA10-04301k-v16 is the correct replacement circuit board for a MaxxAir 4401K MaxxFan.

view full answer...

Answer 6

The part shown in the photo you kindly provided is the manual lift operator. We offer a replacement as part #MA10-20281K-3CF which is compatible with the #MA00-04401M MaxxAir MaxxFan Mini you have.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Correct Replacement Circuit Board for the MaxxFan 4401K Roof Vent

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching