Correct Trailer Hub Assembly for 2,200 lb Timbren Axle-Less Trailer Suspension

Question

Question:

I am looking at this but want to make sure I purchase the right hubs for it. ASR1THDS01

asked by: Graeme

0

Expert Reply:

If you're looking for an idler hub, the # 84545UC1-EZ you looked at will fit. The heavy duty Timbren Axle-Less Trailer Suspension # ASR1THDS01 uses a larger spindle with a 3,500 lb axle bearing combination. If you would like a hub and drum assembly, you can use the # 84546UC3-EZ along with the # 23-468-469 for brakes.

expert reply by: Robin H

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 12

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...