Picking Out Replacement Center Cap for 16 inch Trailer Wheel

Question

Question:

I need a center cap for a 16x7 8 lug wheel but I need Your help matching it up

asked by: Kyle L

0

Expert Reply:

The trick to picking out replacement wheel center caps is to go with the size that matches the center pilot hole of the wheel you have. Most 16 inch trailer wheels with an 8 bolt pattern have a pilot diameter of 4.9 inches like what the # AM90156C is designed to fit.

I also attached a link to a page that has all of the wheel center caps we offer as well.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 3

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 4

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

The overall size of the Furrion Over the Range RV Convection Microwave part#FMCM15SS is 29-15/16" wide x 16-3/8" tall x 15" deep and requires a 30" cutout. If this matches the opening and size of the model you have this will be a…

view full answer...

Picking Out Replacement Center Cap for 16 inch Trailer Wheel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching