Troubleshooting Furrion Vision S Observation System Where Only Gridlines Appear

Question

Question:

The screen wont turn on, it just has lines.

asked by: Victor M

0

Expert Reply:

Sounds like you are just seeing the grid lines but nothing from the camera feed. This is probably an issue with the camera. I would verify that it has power and ground and if so try pairing again. Pairing is done by holding down the pair button on the camera.

expert reply by: Jameson C

0

Answer 1

Yes, the Replacement 7" Monitor for Furrion Vision S Wireless RV Camera System #FR47FR and the Replacement 4.3" Monitor for Furrion Vision S Wireless RV Camera System #FR77FR are compatible with and use the same cameras.

view full answer...

Answer 2

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 3

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

In order to match up the wheel studs for your Reliable 1206 hub, we'll need to know the full dimensions of the wheel stud you're replacing. In addition to the total length of the stud and its diameter and thread pitch, we'll also need to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The Buyers Products 45 Ton Pintle Hook #337PH45 does not have the 4 inch square bolt pattern but rather uses a different pattern. Vertically the holes are 3 inches on center. Horizontally the top row is 5-1/4 inches on center and the bottom is 6-1/2…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

The Hayes Air Actuated Trailer Brake Controller - 1 to 4 Axles - Proportional #HA100400C mounts to the inside of your 2007 Nemar Essex at the dash just like other electric brake controllers will. It needs to be installed on the inside of the vehicle…

view full answer...