Picking Out Replacement Lift Motor for Fan-Tastic RV Fan

Question

Question:

I have the 2000 rdms or the 2000 dms fantastic fan not sure which one from a 1998 bluebird wanderlodge. Do you carry the lid lift motor?? THX

asked by: Don

0

Expert Reply:

The number you mentioned is actually not a part number but we do have lift motors that would potentially work. To find out which lift motor you need there should be a number 7 or 17 on the actual motor, which is the RPMs of that motor.

If the motor has a 7 on it the correct replacement is Replacement Lift Motor for Fan-Tastic Vent B Series Roof Vents with Powered Lifts # FVK6050-80 while if it has 17 on it then the correct part is # FVK6010-81 (White) or # FVK6010-80 (Off-White).

expert reply by: Jameson C

0

Answer 1

The old screen design that you have now which was secured via screws around the outer perimeter has since been axed in favor of the plastic tabs that you see on the Replacement Bug Screen for Fan-Tastic Vent RV or Trailer Roof Vents part #FVK2034-80…

view full answer...

Answer 2

The correct replacement arm for your Fan-Tastic Vent roof vent is the Replacement Lift Arm for Fan-Tastic Vent Roof Vents #FVK8011-05. The replacement arm is the same for the power lift and the manual vent.

view full answer...

Answer 3

According to my research the Replacement Lift Arm for Fan-Tastic Vent Roof Vents #FVK8011-05 should be what you're looking for. Attached is a review video for you to check out.

view full answer...

Answer 4

I could not locate that specific motor number for anything that we have. If you can provide me with the model number of the fan that you have, that would help me ensure that you get the correct replacement motor. However, the Replacement 17-rpm Lift…

view full answer...

Answer 5

I have attached for you below a few wiring diagrams for the Dometic DV4100 Roof Vent Fan which I have received from the manufacturer directly.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Picking Out Replacement Lift Motor for Fan-Tastic RV Fan

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching