Replacement 12 Inch Round Screen for Fan-Tastic Vent

Question

Question:

I have a 1999 fantastic fan model 4000 in my camper van. The screen had 8 screws but the plastic degraded and the screw holes broke, so previous owners made 8 new holes! The entire screen with plastic ring is 12 and 5/8inch in diameter and the hole in the bottom of the fan is 11 and 11/16 inches. What model of pop n lock will fit?

asked by: Claire

0

Expert Reply:

The old screen design that you have now which was secured via screws around the outer perimeter has since been axed in favor of the plastic tabs that you see on the Replacement Bug Screen for Fan-Tastic Vent RV or Trailer Roof Vents part # FVK2034-80 and part # FV2034-10. Therefore, these are the correct replacements for your old screen.

expert reply by: Conner L

0

click to enlarge

Answer 1

The number you mentioned is actually not a part number but we do have lift motors that would potentially work. To find out which lift motor you need there should be a number 7 or 17 on the actual motor, which is the RPMs of that motor. If the motor…

view full answer...

Answer 2

According to my research the Replacement Lift Arm for Fan-Tastic Vent Roof Vents #FVK8011-05 should be what you're looking for. Attached is a review video for you to check out.

view full answer...

Answer 3

The correct replacement arm for your Fan-Tastic Vent roof vent is the Replacement Lift Arm for Fan-Tastic Vent Roof Vents #FVK8011-05. The replacement arm is the same for the power lift and the manual vent.

view full answer...

Answer 4

Thank you for the photo of your 12-inch bug screen from your Fantastic Vent for which you need a replacement. Fantastic Vent's new design screen, which does NOT have the eight mounting holes, will work fine in place of yours. Part…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

The Gen-Y Hitch 5th Wheel to Gooseneck Pin Box part #GY58GR is primarily designed for long bed trucks. It's no different than a standard fifth wheel pin box in regards to the size. If you were using a fixed hitch and standard pin box before with…

view full answer...

Answer 12

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Replacement 12 Inch Round Screen for Fan-Tastic Vent

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching