Backspacing of Dexstar Conventional Steel Wheel with +0.5" Offset - 16" x 6" Rim

Question

Question:

What is the measure from the mounting surface to the inside edge of the rim? Backspacing?

asked by: Richard S

0

Expert Reply:

The Dexstar Conventional Steel Wheel part # AM20766 is a 6" wide wheel which has a positive offset of .5" therefore, the backspacing is 4".

expert reply by: Conner L

0

Answer 1

You can measure the diameter of the wheel and the diameter of the baby moon mounting ridge on the wheel if you care to (see photo), but because the Dexstar Conventional Steel Wheel you have is a standard automotive size, you can simply purchase…

view full answer...

Answer 2

The Americana Conventional Steel Wheel, part #AM22691, has a positive offset of .5 inches. This means that the mounting pad of the wheel would sit .5 inches closer to the outside of the rim which moves the tire closer to the vehicle. This would…

view full answer...

Answer 3

To determine whether or not the Dexstar Conventional Steel Wheel w/ +0.5" Offset #AM20766 will fit your 1952 GMC Pickup you will simply need to compare the specs. The rim dimensions are 16" diameter x 6" wide Bolt pattern…

view full answer...

Answer 4

The best option we have for a vintage style hub cap is the Americana Baby Moon Trailer Wheel Center Cap part #AM90086 which is specific to the Dexstar Conventional Steel Wheel part #AM20766. I could not confirm fit of any other style hub cap for…

view full answer...

Answer 5

Do you see the three raised bumps on the center circle section of your wheel? That's where a baby moon like the part #AM90086 fits over. You need to measure that diameter. If it's right at 9-1/4 inch this cover is what you'd…

view full answer...

Answer 6

For the Dexstar Conventional Steel Wheel part #AM20766 that you are interested in we do not carry any babymoon covers that would fit but we do have more traditional hub covers like the part #PXQT865CHN.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 12

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Backspacing of Dexstar Conventional Steel Wheel with +0.5" Offset - 16" x 6" Rim

Product Page this Question was Asked From

Continue Researching