Center Cap Solution for Dexstar Conventional Steel Wheel part # AM20766

Question

Question:

I am purchasing your 16/6 8 lug dexstar rims. do you have any retro looing center caps that fit these wheels?

asked by: Robert H

1

Helpful Expert Reply:

For the Dexstar Conventional Steel Wheel part # AM20766 that you are interested in we do not carry any babymoon covers that would fit but we do have more traditional hub covers like the part # PXQT865CHN.

expert reply by: Jameson C

1

Answer 1

For your Dexstar conventional steel wheel #AM20766 you cannot use the Americana Baby Moon Trailer Wheel Center Cap #AM90086 or the pointed top baby moon #AM981306 because they only fit up to 15 inch wheels. Other options are to use the center cap…

view full answer...

Answer 2

The #PX1309SS Phoenix USA Baby Moon hub caps are compatible with the #AM20766 Dexstar 16 inch conventional steel wheel you referenced. This being said, we sell these wheels as trailer wheels. They aren't intended for use on a passenger vehicle.

view full answer...

Answer 3

The Dexstar Conventional Steel Wheel #AM20766 will accept the Phoenix USA Baby Moon Hubcap #PX1309SS without modification. This hub cap is stainless steel so it will not flake or peel like some chrome hub caps.

view full answer...

Answer 4

You can measure the diameter of the wheel and the diameter of the baby moon mounting ridge on the wheel if you care to (see photo), but because the Dexstar Conventional Steel Wheel you have is a standard automotive size, you can simply purchase…

view full answer...

Answer 5

Those look a lot like the Lynx wheels such as those found in tire and wheel combo #LHAS701. If your wheels have a 4.9 inch center hole diameter you can use #490EZ-SS, #AM90156C, #LHCS109, or #LHCS109-SI60C. If you have a different size pilot hole let…

view full answer...

Answer 6

The wheel numbers you gave are not giving me anything to help you find the replacement you need. The D60 refers to the axle which is a Dexter 6,000 lb round axle and the 8 refers to the hubs being 8 stud. I can't find anything on the other info.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Center Cap Solution for Dexstar Conventional Steel Wheel part # AM20766

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching