Will Reese Signature Series 5th Wheel Hitch 30057 Fit a Ford F-350 with Factory Prep Package

Question

Question:

Will a Reese 16k Model: 30057 fit an F350 with a standard OEM Ford puck system?

asked by: Anissa

0

Expert Reply:

Yes, the Reese Signature Series 5th Wheel Hitch 30057 will fit a Ford F-350 with factory prep package.

expert reply by: Conner L

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 2

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 6

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 10

There is a way to to a fifth wheel trailer with your 2020 Ram 2500 that has the Ramboxes but you have to install a Sidewinder pin box on the trailer so that the pivot point is raised up high enough that there isn't interference between the pin…

view full answer...

Answer 11

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 12

Yes, it will! The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches item #BWRVR3200 includes industry standard 5th wheel rails that are compatible with the Reese 30032 5th wheel hitch. The Reese 30032 uses the same…

view full answer...

Will Reese Signature Series 5th Wheel Hitch 30057 Fit a Ford F-350 with Factory Prep Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching