Replacement Hardware For a Curt Trailer Hitch Receiver # C13119 to Fit a 2013 Honda CR-V

Question

Question:

I need the hardware to install a CURT 13119 hitch on a 2013 Honda CRV. Can I get just the hardware kit? Also what is the best and wiring I need for the same vehicle to install myself?

asked by: Dennis

1

Helpful Expert Reply:

You will need to order our Replacement Hardware Kit # RHK to get the installation hardware. Be sure to enter the receiver # C13119 when ordering so you get the correct hardware for this receiver to fit on your 2013 Honda CR-V. Be sure to use a Brush # 814092 to clean out the threads of the factory nuts in the frame on your CR-V. This will help to reduce the chances of damaging the hardware during installation.

I recommend installing the T-One Vehicle Wiring Harness # 118561. This harness will give you a 4-way flat connecter and allows for a plug and play installation.

expert reply by: Bud M

1

Answer 1

The bolts that are used are Class 5 if they are Silver and Class 8 is they are a Gold color. If you are looking for replacement hardware for your Curt #14001 Trailer Hitch, you can use the Replacement Hardware Kit, part #RHK. All you need to do is…

view full answer...

Answer 2

For the hardware used to install trailer hitches on your 2013 Honda CR-V it will depend on the hitch. Draw-Tite Class III hitch #75742 and Class II hitch #36520 use Hex Bolt M10X1.25X30 CL8.8 and a 3/8-16 U-Bolt. Curt trailer hitch #C11555 uses…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Hardware For a Curt Trailer Hitch Receiver # C13119 to Fit a 2013 Honda CR-V

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching