Replacement Speed Knob for a Yakima Dr. Tray for 2" Receivers

Question

Question:

Hello, I am looking for a replacement SpeedKnob for Yakima Dr Tray with 2 inch receiver. I can only find the ones for the 1.25inch receiver. Yakima said the 8880717 is only for the smaller receiver, not the 2 inch that I have. Any help?

asked by: Kristi K

0

Expert Reply:

For your Yakima Dr.Tray Bike Rack for 2 Bikes Y02473 that is designed for a 2" receiver, you'll just need the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks # 8880508.

expert reply by: Bryce D

0

Answer 1

The correct replacement SpeedKnob for the Yakima Dr.Tray 2 Bike Platform Rack is actually the Replacement SpeedKnob and Wedge Assembly for Yakima Bike Racks part #8880717 which is slightly longer than the Replacement SpeedKnob and Wedge Assembly for…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 7

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 8

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Answer 9

The 07100 bearing number you referenced is an older bearing that has the same dimensions as #L44643. If both the inner and outer bearings on your existing trailer are the 07100/ #L44643, and the hub has a 4 on 4 inch bolt pattern, the correct…

view full answer...

Answer 10

Hi Phillip, John installed the Furrion Arctic RV Refrigerator w/ Freezer #FR62PJ in a 2019 Grand Design Momentum. In the video he did up having to take the top fascia board off and trimmed it down to fit the new fridge. To cover the gaps on the sides…

view full answer...

Answer 11

Yes we have the Redarc In-Vehicle BCDC Battery Charger #RED96FR which essentially is the same thing as the charging system you referenced as it gives you a way to enhance the charging circuit ran to your 7-way to put the best charge on the trailer…

view full answer...