Fit of Curt 2 Inch Bumper Hitch # E-3S on 2014 Tacoma Double Cab

Question

Question:

Will hitch # E-3S fit 2014 Toyota Tacoma Double Cab?

asked by: Ecn

0

Expert Reply:

The Curt bumper hitch you referenced, part # E-3S is a multi-fit application that will fit many different vehicles. The hitch is compatible with a standard step bumper, so if your Tacoma has that type of bumper it should work. I have provided a photo showing the bolt hole spacing of the hitch that you can compare to your bumper.

The hitch has a 5000 lb towing/500 lb tongue weight capacity that will be limited by the capacity of the truck or the bumper itself if it is lower.

expert reply by: Mike L

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 4

The underside of the standard 2023 Hyundai Elantra is different than the hybrid model of the 2023 Hyundai Elantra Hybrid, which is why the #DT75MR won't fit. There is a hitch designed specifically for the hybrid which has different attachment…

view full answer...

Answer 5

Yes, we do. For your 2023 Hyundai Elantra sedan, I recommend the Curt Trailer Hitch item #C53NR. This hitch is confirmed to fit all models of the 2023 Elantra except for the N and N-Line trims. The Curt Trailer Hitch item #C53NR is custom fit and…

view full answer...

Answer 6

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Answer 7

The Demco 50-Degree A-Frame Coupler without Jack Hole part #DM15349-52 is not available with a jack hole. If you want to add your own hole to accommodate a jack that would be acceptable.

view full answer...

Answer 8

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 9

The height of the exterior portion of the Ventline Vanair 12-Volt Trailer Roof Vent #VP-543SP that you referenced is 2-5/16 inches.

view full answer...

Answer 10

We do have a trailer hitch receiver that fits your 2024 Nissan Pathfinder, from Curt. The correct part number is the following: - Curt Trailer Hitch Receiver #C46DR

view full answer...

Answer 11

I have a solution for you that is a little higher capacity than the #AM10501 that you asked about. You could use the ST235/85-16 tires in a load range G such as #TTWPRG235R16 which is rated for 4,400 pounds at 110 psi. Four of these would have an…

view full answer...

Answer 12

The latching mechanism of your gooseneck trailer coupler needs to wrap around the neck of the hitch ball and does not latch to the top of the ball your like your picture and description implies. You would not be safe to continue to tow like this as a…

view full answer...

Fit of Curt 2 Inch Bumper Hitch # E-3S on 2014 Tacoma Double Cab

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching