Parts Needed to Install 7-Way on 2023 Kia Telluride

Question

Question:

Do you have a 7-pin wiring harness thatll work with a 2023 Kia Telluride?

asked by: Ed F

0

Expert Reply:

I have a way to install a 7-way on your 2023 Kia Telluride but we don't have any custom fit options. Instead you would need to start with a 4-way like the Curt # C59236 and then you would need to convert it to a 7-way with the part # 37185.

If the trailer has brakes instead of the 37185 you would need to use the # ETBC7 with a brake controller like the P2 part # 90885.

expert reply by: Jameson C

0

Answer 1

You can definitely install a 7-way on your 2023 Kia Telluride, you'll just need a couple parts to do so: - Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector #C59236 - Universal Installation Kit for Trailer Brake…

view full answer...

Answer 2

The plug-in trailer wiring harnesses for a 2023 Kia Telluride that use the factory tow package port were all recalled due to a fire hazard potential, dealer and aftermarket. That said, we do still have an option for you but you must hardware into…

view full answer...

Answer 3

On a 7-Way connector the suggested minimum wire gauge for the White (ground) wire, the Red or Black (power) wire, and the Blue (brake power) wire is 12 gauge. The minimum wire gauge for the remaining Green (right turn/brake) wire, the Yellow (left…

view full answer...

Answer 4

Trailers that use 12 volt power for accessories or that have a battery will use the 12 volt circuit in a 7-Way trailer connector. If the trailer does not have those items then you would not have to make that circuit active. That means that you…

view full answer...

Answer 5

In order to install a fully functional 4- and 7-Way connector on your 2017 Subaru Outback Wagon you will need to start with a 4-Way harness if you don't already have one. For this I recommend the Tekonsha T-One Vehicle Wiring Harness…

view full answer...

Answer 6

You have to wire a separate 12 volt power wire for the 7-way adapter as it would draw considerably more than what the power wire of your 4-way kit is capable of. The 4-way's power wire will be in use at all times so you couldn't swap…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...

Answer 10

The correct wiring harness for your 2024 Kia Telluride SX Prestige X-Line is the Curt #C29ZV. This plugs into the connection points in your rear cargo area and is compatible with your LED lights. The #TK74CR is only designed to work with the LX and…

view full answer...

Answer 11

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...