Replacement Front Jack For Lippert Ground Control 3.0 6-Point System

Question

Question:

I have a 2021 Brookstone fifth wheel. One of our front jacks on our Lippert Ground Control 3.0 6 point system failed. I just wanted to verify that item # LC305340 or item # LC362485 would be the correct item.

asked by: Carol

0

Expert Reply:

Both would actually work as a replacement front jack for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set # LC675817. It just depends on if you want the jack tube only, or the jack tube, motor, and foot.

- Tube/Motor/Foot: Replacement Lead Leg for Lippert Components Ground Control 3.0 # LC305340

- Tube Only: Replacement Front Jack for Lippert Ground Control 3.0 # LC362485

expert reply by: Kyle S

0

Answer 1

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 2

In regards to the Lippert Ground Ground Control 3.0 Leveling System, if you just need a new front leg then this can be replaced with the Replacement Front Jack for Lippert Components Ground Control 3.0 Leveling System part #LC362485. If you need a…

view full answer...

Answer 3

Sounds like you have a Lippert Ground Control auto leveling system on your 2016 Highland Ridge Open Range like the #LC358590. For a replacement front leg you'd just need #LC362485 and you'd be set. The price for this is at the attached…

view full answer...

Answer 4

In regards to the Lippert Ground Control 3.0 Leveling System (what you were looking at), there are no replacement inner tubes available. Therefore, if you bent the inner tube on the front leg then you will need to replace the entire leg for which we…

view full answer...

Answer 5

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the jack…

view full answer...

Answer 6

It sounds like you have the Lippert Ground Control Auto Leveling Landing Gear 3.0 part #LC358590 and are looking for replacement front landing gear legs. For that you would want the part #LC305340 . The part number for the rear would be #LC344792 for…

view full answer...

Answer 7

I wish we had just the leg portion of the Replacement Lead Leg #LC305340 but at this time the only way to get it is with the #LC305340.

view full answer...

Answer 8

I wish we offered the front legs of the Lippert Ground Control 3.0 without the motor but the only solution we have is the #LC305340 which includes the motor and the leg.

view full answer...

Answer 9

The B&W Patriot 5th Wheel Trailer Hitch w/ Slider part #BWRVK3270 does not use pins to slide in and keep the handles from raising up. In this design they decided they were not needed as when the head is slid down onto the base the handles rotate…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

For front leg replacements for the Lippert Ground Control systems we have the part #LC362485 for just the leg portion or the part #LC305340 for a leg with the foot and motor as well. These will be the same length as what you have currently.

view full answer...

Answer 12

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...