Replacement Lead Leg Recommendation for Lippert Ground Control

Question

Question:

I have the above lead legs on my 2017 Arctic Fox 29-5T and the screw lifting mechanism has failed mechanically on one of them. The motor and gearbox appear fine. Can I buy just the leg without the motor and bottom pad and if so do you have it in stock? Thanks

asked by: Bob

0

Expert Reply:

I wish we had just the leg portion of the Replacement Lead Leg # LC305340 but at this time the only way to get it is with the # LC305340.

expert reply by: Jameson C

0

Answer 1

I wish we offered the front legs of the Lippert Ground Control 3.0 without the motor but the only solution we have is the #LC305340 which includes the motor and the leg.

view full answer...

Answer 2

It sounds like you have the Lippert Ground Control Auto Leveling Landing Gear 3.0 part #LC358590 and are looking for replacement front landing gear legs. For that you would want the part #LC305340 . The part number for the rear would be #LC344792 for…

view full answer...

Answer 3

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 4

Both would actually work as a replacement front jack for your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set #LC675817. It just depends on if you want the jack tube only, or the jack tube, motor, and foot. -…

view full answer...

Answer 5

The B&W Patriot 5th Wheel Trailer Hitch w/ Slider part #BWRVK3270 does not use pins to slide in and keep the handles from raising up. In this design they decided they were not needed as when the head is slid down onto the base the handles rotate…

view full answer...

Answer 6

The "Out of Stroke" error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 4-Point Set #LC358590 and 6-Point Set #LC675817 means that they have reached the max height, can no longer lift so you need to relocate your…

view full answer...

Answer 7

For front leg replacements for the Lippert Ground Control systems we have the part #LC362485 for just the leg portion or the part #LC305340 for a leg with the foot and motor as well. These will be the same length as what you have currently.

view full answer...

Answer 8

No, the hall effect motor does not have to be greased, but per the service manual if the jacks are down for an extended period, it is recommended to spray the exposed leveling jack tubes with lubricant every 3 months for protection. If you live in a…

view full answer...

Answer 9

The correct replacement front landing gear leg for a Jayco Seismic 310 with Lippert Auto Level System is the Replacement Front Jack for Lippert Ground Control 3.0 Leveling System part #LC362485.

view full answer...

Answer 10

In regards to the Lippert Ground Ground Control 3.0 Leveling System, if you just need a new front leg then this can be replaced with the Replacement Front Jack for Lippert Components Ground Control 3.0 Leveling System part #LC362485. If you need a…

view full answer...

Answer 11

On your Lippert Ground Control System, the cause of the failure of the nut inside the jack could be an overloaded trailer, a blent leg, a bent screw. A lack of grease can cause the nut or the screw to strip threads under load. If your trailer is…

view full answer...

Answer 12

Yes, we offer the Replacement Front Jack for Lippert Components Ground Control 3.0 Leveling System part #LC362485 which is the same as the Replacement Lead Leg for Lippert Components Ground Control 3.0 Electric Leveling System part #LC305340 except…

view full answer...

Replacement Lead Leg Recommendation for Lippert Ground Control

Product Page this Question was Asked From

Continue Researching