Replacement License Plat Bracket Removal and Installation On Yakima Rack & Roll Trailer

Question

Question:

I need to replace the license bracket due to an accident. Any installation tips?

asked by: Carol A

1

Helpful Expert Reply:

I have linked the assembly video we did on the Yakima Rack and Roll Trailer # Y08107 which will help guide you through replacing the License Plate Kit # 8880166. The installation begins around the 4:40 mark in the video for the installation of the license plate bracket. Removal will be the reverse of install.

expert reply by: Bud M

1

Answer 1

The bracket of the Replacement License Plate Kit for Yakima Rack and Roll Trailer #8880166 is made of plastic to keep weight down.

view full answer...

Answer 2

I spoke with my contact at Yakima and found that the tires on the Rack and Roll trailer, #Y08106, are DOT rated. Trailer tires are tested to 65 miles per hour to meet DOT standards, so we cannot recommend towing the Rack and Roll trailer faster than…

view full answer...

Answer 3

The color of the lens of the Replacement Side Marker Light #Y8880178 that you referenced is amber. This is the replacement lens for the clearance light up near the front crossbar of the Rack and Roll trailers like part #Y08107.

view full answer...

Answer 4

The inner width of the Yakima Skinny Warrior part #Y07014 that you referenced is 21 inches and the inner length is 53 inches.

view full answer...

Answer 5

I have another option for you but unfortunately the Yakima Rack and Roll Trailer #Y08107 cannot accept any other style of crossbar, as it was only designed to use the round Yakima crossbars. Instead I recommend the Yakima EasyRider Double Decker…

view full answer...

Answer 6

The Malone MegaWing Kayak Carrier #MPG207 referenced in your question is a great option for your Old Town Fishing Kayak that weighs around 120 pounds. The MegaWing is made specifically for heavier fishing kayaks like this and its 150 pound weight…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Replacement License Plat Bracket Removal and Installation On Yakima Rack & Roll Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching