Is Image Supposed to be Reversed on the Hopkins Smart Hitch Backup Camera and Hitch Aligner System

Question

Question:

I installed the system today, i placed a bicycle behind the truck and image on the screen is reveresd just like the view in a mirror, is it supposed to look that way?

asked by: Stacy L

1

Helpful Expert Reply:

Yes, this is normal. I have the Smart Hitch Backup Camera and Hitch Aligner System, # HM50002, and it does show the same image orientation as the mirror. I am actually glad it does because if it did not, it would be awkward looking at it and then the mirrors and back to the monitor again. It would get a little confusing.

expert reply by: Michael H

1

Answer 1

I spoke with Hopkins about the Hopkins Rear View Camera with Backup Sensors part #HM60195VA and they informed me that there isn't any sort of settings to adjust on the monitor to flip or reverse the view. Therefore, if the view is flipped or…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Hi Jeff; thanks for the question and sturdy is definitely a good word for the etrailer tonneau that fits your 2022 Ram 1500 with a 5-1/2 foot bed, the etrailer Hard Tonneau Cover #e35DR. It's made of a fiberglass-reinforced plastic which is a…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 9

It is certainly possible for the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box #GY58GR to work on your 2020 Ford F-250 Super Duty short bed, but there are likely going to be clearance issues as these are meant for long bed trucks. That…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The best way to prevent any clearance issues with your 2022 KZ Durango Gold G356RLQ and your 2020 Chevrolet Silverado 2500 with 6-1/2' bed and factory puck system is by using the Demco Autoslide 5th Wheel Hitch #DM79GV. This hitch slides back and…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...