What Are The Gear Ratios For The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F?

Question

Question:

What the the gear ratios

asked by: Camden F

0

Expert Reply:

The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F has a high gear ratio which is 6.43 handle revolutions per inch of travel, and the low gear ratio which is 22.86 handle revolutions per inch of travel.

expert reply by: Bud M

0

Answer 1

First, put the magnet ground wires nearby the magnets on the trailer frame. Running them far away makes it harder for the system to complete the circuit. You mentioned that power is getting to the magnets but how much power? TO determine that you…

view full answer...

Answer 2

Dexter recommends a SAE 90, SAE 80W-90 or SAE 75W-90 oil to be used. I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE as it is a synthetic 90 weight oil that helps reduce friction and to keep bearings cool. Since your cap…

view full answer...

Answer 3

The humming sound you hear from your trailer's electric drum brakes is a good sign. It means that the brakes' magnets are being energized by the output from the trailer brake controller in the vehicle. The issue with the brakes not applying…

view full answer...

Answer 4

Yes, the Dexter axle part #8327816 that you referenced has the exact same spindle as a Lippert 5,200 lb axle so the hubs and bearings would interchange.

view full answer...

Answer 5

I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE. This oil is formulated to work with all oil bath style hubs. It is a synthetic 90 weight oil that reduces friction and works well in cold and hot weather applications.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

What Are The Gear Ratios For The Square 2-Speed Jack w/ Crank # TJD2SP-12000SP-F?

Product Page this Question was Asked From

Continue Researching