Replacement Pigtails for Optronics LED Trailer Tail Light

Question

Question:

I have an Optronics STL42RB light on my trailer. The pigtail feed plug has gone bad. Is it possible to purchase this plug assembly?

asked by: Chris W

0

Expert Reply:

Yes, there are a couple of replacement pigtails for the Optronics LED Trailer Tail Light item # STL42RB. One is a right angle plug the other is a standard. I have listed them both below.

Right Angle 3-Wire Pigtail for Optronics Trailer Lights item # A47PB

3-Wire Pigtail for Optronics Trailer Lights item # A45PB

expert reply by: Jerred H

0

Answer 1

This sounds like a ground issue. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light. Make sure that the vehicle side and…

view full answer...

Answer 2

Yes, you can run the switch power wire to a clearance light but the trailer would have to be connected to the vehicle with the running lights on for the interior lights to have power. Aluminum does not offer the best ground so if the lights do not…

view full answer...

Answer 3

When it comes to wiring an LED taillight like the Sealed 4" Round LED Trailer Stop, Turn and Tail Light #STL42RB with Pigtail Harness, #A45PB, the red wire is for stop and turn, the black for running lights, and the white wire will need to be…

view full answer...

Answer 4

The GloLight LED Trailer Tail Light #STL111RFB has mounting holes which are 3/4" in diameter. You would also need a 3-wire pigtail #A45PB or #A47PB to connect the light to your trailer or vehicle. I've added links to video reviews of these…

view full answer...

Answer 5

You can absolutely replace the incandescent lights on your livestock trailer with LED assemblies. Other than replacing the lights themselves, there is nothing else that you will need to do. Your existing wiring (assuming it is in good condition) can…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...