Distance from Jack Foot to Mounting Bracket on Electric Jack EJ-3527-BBX

Question

Question:

Whats the height from where it mounts to the bottom of the jack? Want to make sure it wont stick out very far below the frame of the tongue.

asked by: Scott M

0

Expert Reply:

The bracket height or distance from the mounting plate to the bottom of the jack foot on the Electric Jack part # EJ-3527-BBX is 9" while retracted. I have attached for you below a photo with this dimension.

expert reply by: Conner L

0

Distance from Jack Foot to Mounting Bracket on Electric Jack EJ-3527-BBX
(click to enlarge)

Answer 1

Our etrailer Electric Jacks Electric Jack w/ Footplate #EJ-3527-BBX are made by Pacific Rim. They also manufacture the Ram Jacks right alongside the etrailer.com jacks. Ram is a well known brand of dependable jacks in the industry and many trailer…

view full answer...

Answer 2

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX uses a 7-way RV-style plug. I have included a diagram that shows the pin-out for RV style 7-way plugs. This will show you what each pin does. I have also listed the functions below and linked…

view full answer...

Answer 3

I attached a picture that I got from RAM jacks that shows how the RAM Jack switch part #EJ-3520-PSW that you referenced gets wired up.

view full answer...

Answer 4

The manual emergency crank for the etrailer.com Electric Jack #EJ-3527-BBX (which is included) requires a 3/8" socket for operation. I have attached a short video review on this jack that you can check out as well.

view full answer...

Answer 5

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX that you referenced has a height of 20-1/2 inches from where it mounts to your trailer frame to the top of the jack.

view full answer...

Answer 6

Measurements for the Replacement Strike Plate, #BA29VR, are 3-7/8" length and 1-1/8" wide. Please see the attached product review video with measurements.

view full answer...

Answer 7

The etrailer brand #EJ-3527-BBX is equipped with a 7-way plug that technically can be plugged into the 7-way trailer connector on your 2020 Ford F-150, but it will not function due to the "intelligent" towing package these come with now.…

view full answer...

Answer 8

Yes, the etrailer Electric Jack #EJ-3527-BBX will fit your 2019 Airstream Basecamp X Travel Trailer. It will bolt in the same place that your current manual jack sits. This model is designed to plug into the 7-way on your tow vehicle to power the…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Distance from Jack Foot to Mounting Bracket on Electric Jack EJ-3527-BBX

Product Page this Question was Asked From

Continue Researching