Cable Length for Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers

Question

Question:

How long is the included cable?

asked by: Mark

0

Expert Reply:

The Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers part # GP37MR comes with a 25' cable.

expert reply by: Conner L

0

Answer 1

I contacted the manufacturer regarding your questions. They informed me that the MPPT 40A solar controller does only have the setting for AGM and no lithium setting. This setting is only for the solar controller and will still charge the battery, it…

view full answer...

Answer 2

To set the battery type of your Go Power MPPT Solar Charge Controller - 30 Amp - 12V and 24V #GP72RR you need to have the Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers #GP37MR. Once you have it installed you can use the…

view full answer...

Answer 3

For your 2022 Ford F-150, I recommend the: -Air Lift LoadLifter 5000 Ultimate Plus Air Springs w/ Internal Bumpers #AL54JQ. Reason being is that unlike the Air Lift LoadLifter 5000 Air Helper Springs #AL67PD, these springs have an internal jounce…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...