How to Adjust Hitch Head Angle of Reese Strait-Line Weight Distribution Hitch # RP66074

Question

Question:

I have a rp66074 where do I fine the chart to fine the height of trunnion bar. to set the angle of the head

asked by: Tommy C

0

Expert Reply:

The complete installation instructions for the Reese Strait-Line Weight Distribution Hitch # RP66074 are attached for your reference. While these do provide complete adjustment instructions for the hitch head angle the chart you referred to (from page 2 of the instructions) is also provided in the linked photo.

The chart includes images of several coupler styles and provides the spring bar height (dimension Y) based on the coupler style and measured coupler height.

You might refer to the linked video as well.

expert reply by: Adam R

0

click to enlarge

Answer 1

The Reese weight distribution system #RP66542 uses 3/4 inch bolts to hold the head to the shank. The instructions, linked for reference, state the torque rating. The instructions that are linked are always going to be the most updated version so…

view full answer...

Answer 2

Anytime the fully loaded and ready to tow trailer weight is greater than 50 percent of the weight of the tow vehicle, using weight distribution should be considered. When you get the pop-up, hitch it to the vehicle and pay special attention to the…

view full answer...

Answer 3

Weight distribution heads are adjustable to get the spring bars level or just below level with the trailer frame. Depending on the trailer frame, the head may need to be set at 90 degrees, it also may need to be tilted down as far as possible to keep…

view full answer...

Answer 4

When making the final adjustment for the Reese Dual Cam High-Performance Sway Control, part #RP26002, the 2 nuts should be loose before making the left and right turns. Having the nuts loose will allow them to move and settle into the correct…

view full answer...

Answer 5

In the Reese Weight Distribution System, part #RP67509, the block style washers are used to adjust the tilt of the weight distribution head. This uniquely shaped washer can be rotated and positioned between blocks on the weight-distribution head for…

view full answer...

Answer 6

The hitch ball angle adjustment on weight distribution systems is designed to provide more or less distribution of the tongue weight on your trailer hitch to the trailer and vehicle axles. If you adjust the ball angle farther away from the towing…

view full answer...

Answer 7

If you want to eliminate sag and improve ride quality when towing your Fleetwood Santa Fe, a weight distribution system would be your best option. Suspension enhancement products, like the Timbren springs, #TDVRRT, were originally designed to help…

view full answer...

Answer 8

To determine if you have the correct system for your trailer tongue weight, you should determine the fully loaded and ready to tow tongue weight of your trailer. The weight of any gear stowed behind the rear axle of the tow vehicle also needs to be…

view full answer...

Answer 9

When you tilt the ball of a weight distribution system rearward on your hitch (toward the trailer) you are changing the physics of the system and therefore also the tension on the rear of the trunnion spring bars. Tilting the head rearward will take…

view full answer...

Answer 10

The trunnion bars on your weight distribution system do need to be parallel to the ground in order to operate properly. The goal of a weight distribution system is in part to help stop sag, however, so I would double check just to ensure everything…

view full answer...

Answer 11

With a Reese weight distribution system that has a Dual Cam system part #RP26002 installed you can turn about as tightly as you'd ever need to going forward, but when in reverse you'd have to be careful as it's much easier to jackknife a…

view full answer...

Answer 12

We recommend using some sort of sway control if the trailer you're towing weighs at least 50 percent of what the tow vehicle weighs or if you're experiencing any sway or sagging. Since the Touareg's owner's manual says to not use a…

view full answer...

How to Adjust Hitch Head Angle of Reese Strait-Line Weight Distribution Hitch # RP66074

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching