Can Charger of Bright Way Push to Test Breakaway Kit Overcharge Battery

Question

Question:

It looks like the CHARGING led on the breakaway batter charging unit is always lit when connected to the external 12v power. Is there any chance of overcharging the battery or is the battery charger smartfoot enough to go into a trickle charge mode?

asked by: Gerry

1

Helpful Expert Reply:

The Brightway Push to Test Breakaway kit part # 3802311 that you referenced has such a low charge rate at 2 amps that it essentially is always in a trickle charge mode and would not overcharge or damage the battery.

expert reply by: Jameson C

1

Answer 1

Yes, that all sounds correct. The computer systems on the newer trucks require a constant draw to provide power to the vehicle's 7-Way connector. To work around this you will need the 7-Way Vehicle Power Adapter item #FR87PR. This plugs directly…

view full answer...

Answer 2

For maximum effectiveness, trailer tires need to be inflated to max psi, which will be somewhere on the tire's sidewall. For example, a load range E tire such as the Westlake ST235/80R16, #LHWL401, has a load capacity of 3,520 lbs when inflated…

view full answer...

Answer 3

It sure will. Per DOT regulations, a properly functioning breakaway system should be able to hold the trailer brakes engaged for a minimum of 15 minutes. Past that point, the battery(s) would wear down pretty quickly if you're speaking of a small…

view full answer...

Answer 4

For a breakaway system with a built-in charger I recommend the Bright Way Push-to-Test Trailer Breakaway Kit #3802311. This is a popular option because it is all in one and has a push to test feature to monitor battery charge level.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The Solera Gas Strut part #LC280343 is designed for Lippert-Solera branded awnings. That said, it should be able to be used with others but you'd need to verify the dimensions in order to ensure compatibility. The length for this strut will be…

view full answer...

Answer 7

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Answer 8

Since the discontinued MaxxAir 4700k model fits a standard 14 x 14 RV vent opening, I recommend the MaxxFan Plus Roof Vent w/ 12V Fan - 10 Speed #MA00-04500K. The MaxxFan Plus comes with a thermostat and a remote for easy temperature customization.…

view full answer...

Answer 9

Using butt connectors such as #05731-5 is probably the fastest way to connect wires. Using a heat shrink butt connector such as #DW05744-5 would be a better, longer lasting connection. The white ground wire will need to secure to the trailer frame…

view full answer...

Answer 10

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Yes, the 12 volt accessory circuit of your trailer wiring would be able to keep a 10 amp breakaway kit battery topped off like the part #3802311. Usually the 12 volt accessory circuit of a 7-way is protected with either a 30 amp or 40 amp fuse.

view full answer...

Can Charger of Bright Way Push to Test Breakaway Kit Overcharge Battery

Product Page this Question was Asked From

Continue Researching