Can Timbren Axle-Less Trailer Suspension Kits Be Used On Triple-Axle Trailers

Question

Question:

Good day, Can I use the Timbren Trailer axle-less Axles - ASR2KHDS03 for a tri-axle setup? There is nothing similar on the market for a tri-axle setup. With kindest regards

asked by: Uwe

0

Expert Reply:

Unfortunately Timbren doesn't recommend using the Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS03 in a triple-axle setup. If you could give me more details on what you're trying to accomplish then I could look into alternatives for you.

expert reply by: Kevin C

0

Answer 1

Axles are there to support the weight of the trailer so increasing the number of axles would not result in a softer ride quality like you're thinking. The suspension, whether it's leaf springs or Timbrens, would be the determining factor in…

view full answer...

Answer 2

The HD Timbren axle less 2k axle kits use the 3,500 lb trailer spindle since it's a little heavier duty which is why the hub/drums and assemblies seem to be rated too high. So the #ASR2KHDS03 does use the #23-468-469 and the #84556UC3-EZ.

view full answer...

Answer 3

We don't carry the complete torsion axle you are looking for, however, I recommend the Timbren Heavy-Duty Axle-Less Trailer Suspension - 4" Lift Spindle - Wide Tires - 2,000 lbs #ASR2KHDS03 that will fit your trailer and will also give you…

view full answer...

Answer 4

That's a good question, and it wouldn't be just the spindle itself that gets replaced on the Timbren Axle-Less systems, it would be the whole spindle arm that would need to be replaced if there was any damage. If you take a look at the photo…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 10

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 11

The maximum deflection or compression/movement of the Timbren Silent Ride Suspension for Tandem Axle Trailers #TSR14K35T01 is 1-5/8 to 1-7/8 inches. That's the amount it will move from zero load to full compression.

view full answer...

Can Timbren Axle-Less Trailer Suspension Kits Be Used On Triple-Axle Trailers

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching