Correct Replacement Remote for a MaxxFan 4401K Roof Vent

Question

Question:

I have a 4401k model maxx fan I need a replacement remote for it I brought a remote from your web site part# 9068-09 will this work with the maxx fan I have or do I need a different remote that will work for that fan

asked by: Israel J

0

Expert Reply:

The Replacement Digital Remote Control for Fan-Tastic Vent Roof Vent with 12V Fan # FV9068-09 you purchased is actually the replacement remote for the Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote # FV807350 and will not work with your MaxxFan Roof Vent w/ 12V Fan # MA00A04401K.

Instead, what you're going to want is the Replacement Remote for MaxxAir Roof Vent Exhaust Only Fan # MA00A01151K.

This is the direct OEM replacement remote for your MaxxFan. Attached is a product review video for you to check out as well.

expert reply by: Bryce D

0

Answer 1

For your MaxxFan that is a 4301 Series the correct circuit board is the part #MA10-04301K-V16.

view full answer...

Answer 2

I spoke with my contact at MaxxAir who said that if you lost the remote to your MaxxAir fan there is no programming that has to be done when using a replacement remote. Part #MA00A01150K is already compatible with all MaxxAir fans that have…

view full answer...

Answer 3

The Maxxair website doesn't list the 4900K as coming with a remote control option. It may have been something added by a manufacturer. The Replacement Handheld Remote for Maxxair Roof Vent Intake/Exhaust Fans - Qty 1 #MA00A01150K or the…

view full answer...

Answer 4

The connection on the Seaflo Submersible Utility Pump #SE54FR is designed to fit a hose with an inner diameter of 13 mm.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

While we do not carry that particular Lippert step we do have the similar MORryde #MR98RR or a better option in my opinion is the TorkLift GlowStep #TLA9104. I prefer this step as it folds up nicely and works better in tight areas like storage lots.…

view full answer...