Is The Progressive Dynamics PD9140 RV Converter Available

Question

Question:

Do you have a model 9140a converter i am unable to find one. And if not do you have a replacement part that is equivalent? Thank you for your time

asked by: William C

0

Expert Reply:

While we don't currently offer the PD9140 we do carry the 45 amp versions with part # PD9245C for lead acid batteries and part # PD9145ALV for lithium batteries. Since these are rated for 45 amps you will most likely need to increase the gauge of wire you have running from your current converter to the battery to 6AWG to be able to safely handle the load.

expert reply by: Kevin C

0

Answer 1

Since your battery bank would essentially be rated for 210 amps the 45 amp rated Progressive Dynamics Inteli-Power RV Converter and Battery Charger #PD9145ALV that you referenced would fully charge both of them in about 4 hours or so. But that…

view full answer...

Answer 2

Sounds like you're needing the Progressive Dynamics Inteli-Power RV Converter and Battery Charger #PD9145ALV which is compatible with the popular lithium batteries and is also rated for 45 amps so it will be a great replacement for your…

view full answer...

Answer 3

In storage mode, the output voltage increases to 14.4v DC for approximately 15 minutes every 21 hours to help prevent sulfation of the battery plates. The converter output should be 13.6. When disconnected from the battery, or when the batteries are…

view full answer...

Answer 4

Yes, the Progressive Dynamics 9100 Inteli-Power Lithium Converter #PD9145ALV would be the correct replacement since you've switched over to lithium batteries. It has the same 45 amp rating so you'll be able to reuse the wiring you already…

view full answer...

Answer 5

The Progressive Dynamics Inteli-Power RV Converter and Battery Charger - Lithium #PD9145ALV is designed for 14.6V +/- 0.3V according to the instructions. There isn't a way to adjust the voltage output as this converter/battery charger is designed…

view full answer...

Answer 6

When you move up to a larger amperage converter you just need to ensure that your wiring is the correct gauge to support the higher amperage. Since you're only going from 40 to 45 amps you're more than likely fine. The next important step is…

view full answer...

Answer 7

Great question. I went ahead and brought your questions to my tech at Progressive Dynamics. The Inteli-Power RV Converter and Battery Charger - Lithium #PD9145ALV has 2 recovery stages: 13.6 VDC and 14.6 VDC. The converter automatically switches…

view full answer...

Answer 8

I don't have a fool proof way of selecting the proper charge converter amperage rating because it is not based solely off the battery capacity but rather this combined with the load the trailer uses. Therefore, the best option would be to go with…

view full answer...

Answer 9

In order to choose the correct Progressive Dynamics Inteli-Power RV Converter and Battery Charger like part #PD9145ALV you will indeed need to know the total amp hour battery capacity. That said, there is not an exact formula to determine the correct…

view full answer...

Answer 10

Yes, since you're just replacing the converter you'll just need to unwire it from the IOTA Load Center and then you can wire in a dedicated outlet for the Progressive Dynamics 9100 Inteli-Power Lithium Converter #PD9145ALV to plug into for…

view full answer...

Answer 11

The Progressive Dynamics Inteli-Power RV Converter and Battery Charger - Lithium - 12V - 45 Amps #PD9145ALV is designed for use with lithium batteries and will match the amperage of your WF-8845 converter charger. Built for lithium batteries, this…

view full answer...

Answer 12

Yes, the Progressive Dynamics Inteli-Power RV Converters like part #PD9130LV must be grounded to the chassis which you can see from the photo below which was pulled from the installation instructions.

view full answer...

Is The Progressive Dynamics PD9140 RV Converter Available

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching