How To Determine If Your 2018 Chevy Silverado Has An OEM Prep Package

Question

Question:

I have a 2018 Chevy 2500 and how do I find out if I have or have not a OEM Prep Pkg? Looking to figure out which 5th wheel package I need.

asked by: David C

0

Expert Reply:

It's very easy to determine if your 2018 Chevy Silverado 2500 has the OEM prep package. All you'll need to do is look in the bed and see if you have four underbed mounted pucks for a hitch like the B&W Companion OEM 5th Wheel Hitch for Chevy/GMC Towing Prep Package # BWRVK3700 to drop into. I've attached a video where Conner shows the pucks and how to connect this hitch to them.

You should also have an in-bed 7-way connection if you have the prep package.

If you find that you don't then you will have to go with an above-bed base rail kit or with a below-bed gooseneck/turnoverball hitch.

If you're fine with base rails then I recommend the B&W Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches # BWRVK2506. These rails are designed to work with ISR compatible trailer hitches so you'll have plenty to choose from.

If you'd prefer an below-bed system then I recommend the Custom Underbed Installation Kit for B&W Companion 5th Wheel Trailer Hitches # BWGNRK1016-5W. This hitch would require you to use a Companion # BWRVK3500-5W, but also gives you the ability to tow gooseneck trailers.

The hitch you choose will also need to be compatible with the length of the bed. If you do not have a 8' bed you'll need to use a sliding hitch like the Patriot # BWRVK3270 if you go with base rails or the Companion # BWRVK3400 if you choose the turnoverball hitch.

For in-bed wiring I recommend the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole # PK11893-11932.

If you have any other questions are want to narrow down the right options for your needs then I'd love to hear your feedback.

expert reply by: Kevin C

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the…

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The Ford OEM puck system is different than the Chevrolet/GMC OEM puck system therefore, you can't use a 5th wheel hitch from one in the other. The Ford OEM system has pucks which are much closer together than on the Chevrolet/GMC OEM system. The…

view full answer...

Answer 12

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...