Will the AirLift 1000 part # AL60817 fit a 2013 Jeep Wrangler Unlimited

Question

Question:

Will the product AL60817 fit my 2013 jeep rubicon unlimited rear springs.

asked by: David

0

Expert Reply:

Yes, I checked with Airlift and the Airlift 1000 Air Helper Springs # AL60817 that you referenced are confirmed to fit your 2013 Jeep Wrangler Rubicon.

expert reply by: Jameson C

0

Answer 1

So long as the coils are not different on your lifted 2013 Jeep Wrangler then yes, you can use the Air Lift 1000 Air Helper Springs for Coil Springs - Rear #AL60817.

view full answer...

Answer 2

The Air Lift AirLift 1000 Air Helper Springs for Coil Springs - Rear #AL60817 can utilize spacers to compensate for a lift kit installed on the vehicle. I reached out to my contact at Air Lift and they need the internal diameter of the coil as well…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Will the AirLift 1000 part # AL60817 fit a 2013 Jeep Wrangler Unlimited

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching