Dually Wheel for a Texas Bragg Trailer with 7.50-16 Tires

Question

Question:

IM LOOKING FOR SOME WHEELS FOR A TEXAS BRAGG TRAILER THEY R TANDOM DAULS 8 LUG TIRE SIZE IS 7.50 R 16 DO U HAVE ANY?

asked by: DONNIE

0

Expert Reply:

The 7.50-16 is a light truck tire size sometimes used on trailers. It fits a 16x6 inch wheel. We have several wheels in this size with an 8 on 6-1/2 bolt pattern but since you have dually wheels you will want # AM20783. I have included a link to a video review of this wheel for you.

expert reply by: Michael H

0

Answer 1

The Taskmaster Radial Trailer Tire - Load Range G, item #TTWPRG235R16, is the closest tire to the 7.50-16LT tire that we have. Your tire has an overall height of 31.8 inches and a section width of 8.4 inches. The #TTWPRG235R16, tire has and overall…

view full answer...

Answer 2

It sounds like the problem you are having is related to one of the possibilities you have mentioned. It is nearly impossible to press a race in straight at home unless you have the proper equipment and have done it before. Taking the drums to a brake…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

The difference between the two trailer tire sizes is that the letter D in the first size you listed ST205/75D15 stands for bias ply and the letter R in the tire size that they put on your vehicle stands for radial. Radial tires are preferred over…

view full answer...

Answer 10

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Dually Wheel for a Texas Bragg Trailer with 7.50-16 Tires

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching