Correct Replacement Legs for Lippert Ground Control 3.0 Leveling System - 6 Point

Question

Question:

Can I buy a single replacement jack for Lippert 6 point leveling system? One jack sheared inside and fell off

asked by: Tommy H

0

Expert Reply:

Yes, we do offer replacement jacks for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 6-Point Set part # LC675817. I have attached these for you below by their location on the trailer.

Rear/Middle:

24-1/2" Leg part # LC344792 (RR or RM)
24-1/2" Leg part # LC305339 (LR or LM)
22-1/2" Leg part # LC342610 (LR or LM)
22-1/2" Leg part # LC428493 (RR or RM)

Front:

Replacement Front Jack part # LC362485

Please note, the rear legs only come as a complete assembly with the motor and gear box.

expert reply by: Conner L

0

Answer 1

The distance between the insides of the weld stops on the jack leg #LC362485 is 17-1/2 inches and the outer tube diameter is 2-1/2 inch by 2-1/2 inch.

view full answer...

Answer 2

If you get the Out of Stroke error message on the Lippert Ground Control system, such as #LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further. To clear the error you can extend all of the jacks in…

view full answer...

Answer 3

This has been asked before, and what Lippert has told us is that in order to turn your 4-point system #LC358590 to a 6-point system #LC675817 you'd have to purchase the entire new 6-point system, unfortunately. The two additional jack legs can…

view full answer...

Answer 4

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 5

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 does require adequate power to work properly. I recommend checking your ground connection from your battery to the trailer frame and…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...