Can Master Lock Hitch Receiver and Coupler Latch Lock Set be Ordered With Specific Key Number

Question

Question:

Can we order the set with the specific Master lock key number specifically to match other master lock gear we already own that is keyed alike?

asked by: Sean

0

Expert Reply:

No, unfortunately a specific key number cannot be ordered for the Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches # 2848DAT.

expert reply by: Kyle S

0

Answer 1

For your Master Lock hitch pin, like the Master Lock Hitch Receiver and Coupler Latch Lock Set #2848DAT, you can use the: -Replacement Key for MasterLock Coupler Locks #MLK1. All you'll need to do is type in your key number in the box, and…

view full answer...

Answer 2

Unfortunately, the Roadmaster #RM-316 aren't available keyed alike in multiples greater than the included 2. This being said, I might have an option that would allow you to get as many similar locks as you'd like that would be keyed alike.…

view full answer...

Answer 3

The Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches #2848DAT has replacement keys if you know the key number using #MLK1. If you do not know your key number, unfortunately there is no way to determine…

view full answer...

Answer 4

What I recommend is using Master Lock Hitch Receiver and Coupler Latch Lock Set, #1481DAT. It comes with a coupler latch lock and receiver lock that are keyed alike.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Can Master Lock Hitch Receiver and Coupler Latch Lock Set be Ordered With Specific Key Number

Product Page this Question was Asked From

Continue Researching