Replacement Peterson Trailer Taillight PM 146 and Grommet

Question

Question:

Chenega Healthcare Services Customer Number 7210545 I am checking to see if the parts I have in my online cart are a match to the parts I am trying to replace. Original parts Peterson trailer light PM 146 Grommet 14618 Online cart parts Etrailer Peterson trailer light M146R Rubber Grommet and Pigtail 166-18k

asked by: Steven R

1

Helpful Expert Reply:

Yes, the Peterson trailer light part # M146R and rubber grommet and pigtail # 166-18K are correct replacements for your Peterson trailer light PM 146. This is an exact replacement.

expert reply by: Jameson C

1

Answer 1

The Backing Plate #HP72FR can be cut to match the Tandem Axle Teardrop Trailer Fenders #HP64VR but we do not have any custom backing plates that fit the #HP64VR.

view full answer...

Answer 2

I've got a couple troubleshooting steps you can go through to determine the cause of this, but it sounds like the right side of the trailer is fully functional and the left side isn't. You can start by testing your vehicle's…

view full answer...

Answer 3

The Optronics Fleet LED Trailer Tail Lights w/ Grommets #TLL12RK has grommets that are 1-1/8 inches deep. The plate dimension if you want to use the integrated lip on the grommet is 3/16 inch and if not is up to 1/2 inch. I went out to our…

view full answer...

Answer 4

The Class lV trailer hitch that is designed to fit your 2011 F-150 is the Curt Hitch, part #C14002. This hitch has a 2 inch receiver opening. I went to the warehouse and measured the receiver material. It measures 1/4 inch thick. I measured a Class…

view full answer...

Answer 5

The Light, Red Flush Mounted Sealed Turn Signal - Round #435800 will require holes that are 4-1/2 inches diameter for the grommet to fit properly. I measured this in our warehouse to confirm and have attached a photo to help.

view full answer...

Answer 6

I wasn't able to find much detailed information on the Signal Stat 9031 model light assembly that you mentioned other than that it has been discontinued. In order to see if the Peterson Light Red Flush Mounted Turn Signal #435800 will work well…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Replacement Peterson Trailer Taillight PM 146 and Grommet

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching