Brake Assembly Replacement for 2012 Keystone Montana Big Sky 3520RL

Question

Question:

i have a fifth whell montana big sky model 3520RL 7000lb axel what is the trailer brake kit w dust shield self adjusting left and right hand ,i need to order two kits because i have two axel

asked by: Jean R

0

Expert Reply:

For a set of self-adjusting brake assemblies that fit your 2012 Montana Big Sky 3520RL that has 7k axles we have the TruRyde brake kit part # TRU96FR that is correct fit and would work great. Since you have a tandem axle trailer you'd need to order a quantity of two of these.

expert reply by: Jameson C

0

Answer 1

Yes, the TruRyde Electric Trailer Brake Kit #TRU96FR will fit the 7,000lb Dexter axles on your 2020 Grand Design Solitude 375. We do also have the Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-464-465 if you prefer to keep the axle components…

view full answer...

Answer 2

For your 2020 Grand Design Solitude 375 5th wheel camper you will first need to verify the length of your current shackle straps. These straps are measured from center of bolt hole to center of bolt hole. The MORryde Suspension Upgrade Kit is…

view full answer...

Answer 3

We do! What you're looking for is the Brake Mounting Flange for 3" Round Axle #4-44-1. This is a weld-on installation like what you mentioned.

view full answer...

Answer 4

Since we know your 2015 Jayco HT 27.5RLTS has 5,200 lb axles the correct bearing kit would be the #BK3-310 which comes with the correct bearings, races, seal and tang washer. To pick out replacement shoes I would need to know what brand assemblies…

view full answer...

Answer 5

Since there isn't a way for us to look up what you have you'll need to remove the wheel and possibly the hub/drum to get to the brake assembly. There will typically be some sort of sticker on the inside or on the back of the plate that can…

view full answer...

Answer 6

If it feels like the hubs are getting too hot, one item to check is if the spindle nut is too tight and the added stress on the bearings is overheating the bearings and hub that could cause damage to the bearings. I have attached a video of our…

view full answer...

Answer 7

The TruRyde Electric Trailer Brake Kit #TRU96FR that you referenced is a pair of assemblies that include a left and right assembly. So if you need just a left and a right assembly ordering this part number would get you just that.

view full answer...

Answer 8

The Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-458-459 you have now is designed for 6,000 lb axles and fits 12" x 2" drums. In addition to the Dexter we have the etrailer #AKEBRK-7-SA or the TruRyde #TRU96FR. All three of these are…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Brake Assembly Replacement for 2012 Keystone Montana Big Sky 3520RL

Product Page this Question was Asked From

Continue Researching