Recommended Hitch and Wiring Harness for a 2020 Hyundai Santa Fe

Question

Question:

I have a 2020 hyundia santa fe does the c 13195 come with the necc. wire harness and rubber hitch cover ??

asked by: Tom J

0

Expert Reply:

The Curt Trailer Hitch Receiver item # C13195, that is confirmed to fit your 2020 Santa Fe, does not include a wiring harness or a rubber hitch cover. This hitch is custom fit and bolts to your Hyundai with included hardware.

There are no hitches available that come with the wiring harness and rubber cover.

To add a wiring harness to your vehicle you will need the Curt T-One Vehicle Wiring Harness item # CU94FR. To attach this harness to your hitch to prevent it from being damage you will want the No-Drill Mount for Electrical Mounting Bracket item # 18140 and the Mounting Bracket 4-Pole Flat item # 18144.

For a rubber hitch cover you'll want the Curt item # C22272.

expert reply by: Jerred H

0

Answer 1

The best trailer hitch for a 2020 Hyundai Santa Fe is the Draw-Tite Trailer Hitch Receiver #75908 because it an easy, bolt-on installation, provides the most ground clearance of any hitch for your Santa Fe and has a tab which will let you very easily…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

For your 2020 Hyundai Santa Fe we have a couple of wiring options. These will both offer a 4 way flat trailer connector. They are almost identical they install the same, have the same power output and are designed to protect your vehicle should there…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...