Will the Curt A20 Replacement Head Fit the Mopar 20K Base for Ram Prep Package?

Question

Question:

Can the Curt a20 head be mounted on the legs of a Mopar 20 base?

asked by: Wade

0

Expert Reply:

Yes, the Replacement Head for the Curt A20 5th Wheel Trailer Hitch item # C16540 is compatible with the Mopar 20K base. It is just a rebranded version of the Curt OEM 5th Wheel Hitch Legs item # C65WR that Dodge sells under their Mopar line.

expert reply by: Jerred H

0

Answer 1

Since the gross weight of your Grand Design 311 BHS is less than 14k the 18k Trailair Flex Air pin box part #LC328492 would easily have enough weight capacity and since it's the best cushioned pin box out there you'll be really happy with it…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

The A series of Curt 5th wheel trailer hitches, such as #C16120, is the newest version and is replacing the Q series. The A series jaws overlap whereas the Q series butt up against each other more than overlap. And the bearing and shaft that the head…

view full answer...

Answer 6

The Curt A-Series line is the premium version over the Q-Series line and comes with a few differences. One major difference being the jaw design for the A-Series, which overlaps itself instead of just butting up to itself like the Q-Series does. This…

view full answer...

Answer 7

Yes, you can replace the head of your E16 Curt fifth wheel hitch with an A16 hitch head part #C16520 and have a much better king pin contact which means much less noise.

view full answer...

Answer 8

Yes, the Curt Q20 head part #C16520 can replace the Curt E16 hitch head you have and would work well as a way to upgrade your fifth wheel hitch setup.

view full answer...

Answer 9

There are a couple of ways other than replacing the pin box on your trailer that can help to reduce the chucking you are experiencing. First, I simply recommend checking to make sure the tongue weight of your trailer is around 10-15 percent of its…

view full answer...

Answer 10

We do have the Furrion Standard RV Microwave at 1,350 watts that is a 0.9 Cu Ft unit in black, #FMSN09BL. This has measurements of 29-7/8W x 16-7/8T x 18-3/16D Inch. This does appear to have a higher wattage than the Appollo but if that is an issue…

view full answer...

Answer 11

Since you mentioned the cotter pins which are used to secure the feet inside the rails, that makes me that you are referring to the connection point between the rail and foot on one of the four corners of the Curt A20 5th Wheel Trailer Hitch part…

view full answer...

Will the Curt A20 Replacement Head Fit the Mopar 20K Base for Ram Prep Package?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching