Parts Needed To Install a 7-Way Blade Connector In Bed Of a 2023 Ram 3500

Question

Question:

What will I need to move the 7-way connector from the bumper to the bed on my 2023 Ram 3500?

asked by: Fred J

0

Expert Reply:

You will need the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness # 41157. This kit contains a wiring tee to connect behind your bumper 7-way and a 7-way connector you can install in your bed side. This will allow both the bumper 7-way and in bed 7-way to function without needing to change anything else.

expert reply by: Bud M

0

Answer 1

The best spot to install the Trailer Connector is on the bed sidewall on the drivers side, between the wheel well and the tail gate. We have an installation video showing this Curt 5th Wheel and Gooseneck Wiring Harness #C56000 being installed on a…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

To replace the motor on the LCI Pump 650057 we have the Replacement Motor #LC167576.

view full answer...

Answer 7

Hey Eric, the Curt Multi-Fit Ball Kit w/ 4" Offset for Chevy/Ford/GMC/Nissan Underbed Gooseneck Hitch #C68ZV is not going to work with your Ram, unfortunately. This one is only going to work for select YMM (Year Make Model) Ford 250-450s, GMC…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

Thanks for the photo, that was a big help. And the answer is yes, your 2023 Ford F-350 Cab & Chassis is 100 percent compatible with the Curt 7-way: - Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR…

view full answer...

Parts Needed To Install a 7-Way Blade Connector In Bed Of a 2023 Ram 3500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching