Best Trailer Hitch Receiver and 4-Way Flat Wiring Harness For a 2022 Mazda CX-30

Question

Question:

Can you help me select the best receiver for my 2022 Mazda CX-30?

asked by: Cesar

0

Expert Reply:

I recommend the Draw-Tite Trailer Hitch Receiver # DT44YR as the best for your 2022 Mazda CX-30. The receiver has a 2" opening allowing for a larger selection of hitch mounted accessories and ball mounts. It uses a hidden cross tube allowing for a clean factory appearance.

The T-One Vehicle Wiring Harness # TK67FR will give you a 4-way flat connector. This will allow you to connect to most small trailers you may tow and will allow you to use Auxiliary Lights # C53201. The auxiliary lights are needed if you are using a hitch mounted accessory which impairs the view of your tail lights.

expert reply by: Bud M

0

Answer 1

The Draw-Tite Sportframe Trailer Hitch Receiver #DT64MR has been confirmed to fit all models of your 2021 Mazda CX-30 including your Turbo model and it does not require any drilling either! If you were in need of trailer wiring as well the Tekonsha…

view full answer...

Answer 2

No, wiring the Tekonsha T-One Vehicle Wiring Harness #TK67FR you have to the battery of your 2021 Mazda CX-30 will not cause the battery to go dead due to it only powering the trailer lights when the vehicle is turned on. You will however have to…

view full answer...

Answer 3

The most likely cause for the incorrect behavior of your trailer lights, where activating one turn signal causes all trailer lights to blink, is an insufficient ground (or a short to ground) on either the vehicle or the trailer. Since you re-wired…

view full answer...

Answer 4

We do have the T-One Vehicle Wiring Harness #TK67FR from Tekonsha which is designed to fit your 2021 Mazda CX-30. I have linked an installation video below for this on a 2022 CX-30 which shows it working with a Tester #I26.

view full answer...

Answer 5

The trailer hitches that fit your 2022 Mazda CX-30 like the Curt #C49CR also fit the 2021 models. This also true for the Curt trailer wiring harness part #C86CR that you referenced.

view full answer...

Answer 6

First, use a circuit tester like #PTW2993 on your trailer connector as a helper activates each lighting function and operates the manual brake switch on the brake controller. This helps isolate the problem to the trailer or the tow vehicle. If…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...